#1 24X7 Plumbing and Heating Contractors Suitland 20746 MD (844-507-4350)

Posted by in Heating Contractors, on January 25, 2018

Plumbing Repair Services in Suitland 20746

24X7 Operation & FREE Consultation Click to Call

Plumbing and Heating Contractors Suitland 20746 MD: Got a broken water line? Here is how you can fix it

The water pipe does not give a warning before breaking. You only get to see the results after the deed is done. The sudden gush of water is the obvious indication of a broken water line. When a water line inside the home gets damaged, it is still easy to fix because it is visible. But in case the underground water line breaks, you need to dig deep into the ground and fix it. This means more hassle and expense. You can go through the tips given below to reduce the expenditure and learn how to fix broken water lines yourself.

Some common reasons for the breaking of water lines

Usually, fittings and connections in the water pipe are the first to get affected and develop cracks which leak and eventually erode the PVC pipe to such an extent that it breaks. The underground water lines located under the foundation of the home or between the street and the house break due to deterioration with the passage of time or due to pressure. In some cases, these pipes burst due to freezing. Water lines also break during earthquakes. When you hear a rumbling or hissing sound coming from the main water line even when you are not using any of the faucets, it means that the main water line has developed a crack. Also, when the pressure of water is lower than usual, it indicates the loss of water due to a leak in the pipe. In such cases, it is very important that you know how to fix broken water lines. Or call us today and we can help you find the best Plumbing Emergency Firms in Suitland 20746 MD.

Things that you need to keep in mind before repairing the pipe

It is important to evaluate the condition of the pipe before going for a repair. If the pipe is very old, it is better to replace it rather than trying to repair it. In case the pipe has been repaired before, then too replacement is a good choice. If the pipe has developed a crack for the first time, you should consider removing the whole pipe rather than replacing only the damaged part. The reason is that a repaired pipe is more likely to develop cracks again. So instead of spending money twice on repairing, it is wiser to spend it once and install a new pipe which will last longer. Pipe materials like PVC can be easily repaired but lead based pipes become brittle and corroded with time and hence, need to be replaced.

Plumbing and Heating Contractors Suitland 20746 MD

How to fix broken water lines?

Here are some tips which might prove to be useful in case you want to learn how to fix broken water lines.

  • Locating the point of the leak

The first thing is to find the crack. The cracks in the pipes located inside the house are evident but the underground pipes are not visible. When these pipes break, the accumulation of water above the ground or the wet mud gives an indication of the leak. If the pipe located behind the wall of the home breaks, you need to put your ear to the wall and locate the leak. When your pump is running and the water meter is moving without any of your faucets being on, it means there is a leak somewhere. That is why professionals and Plumbing Contractors Suitland 20746 MD keep an eye on that.

  • Digging under the ground

This advice is given by the top rated Plumbing Repair Services in Suitland 20746 MD. The pipes located underground can be repaired only after you dig them out. This is something which you cannot do yourself. You should find a reputable water main contractor to identify the problem and get it fixed. You also need to call your utility company to mark underground pipes and wires so that they do not get damaged when you dig for the water line. When the water line breaks outside the house, the pipe is dug out from the yard to the house. Then it is cut and removed and replaced with a new pipe. The new pipe should be connected with the existing one and all the indoor and outdoor joints should be sealed. You should always check for leaks after the repair work is over. There is also a no-dig repair method in which a resin pipe lining is put in to the pipe till the place of the break. It is then inflated with air so that it touches the wall of the pipe and hardens to seal the pipe. This is called the Cured in Place Pipe method. A minor break can be repaired by putting a sleeve around the pipe or by replacing only that small portion of the pipe.

Plumbing and Heating Contractors Suitland Maryland

  • Fixing the visible pipes yourself

When you see a sudden gush of water from any pipe of your house, you should first shut-off the main valve. A small leak can be closed by placing a piece of rubber or any other sealing agent available on the leak. You can then put a C-clamp on it to tighten the seal. A sleeve clamp can also be fixed using a screwdriver. It stops both small and large leaks. These plumbing repair items like hose clamps, duct tapes, rubber and C-clamps are very cheap and can be stored at home in anticipation of such problems. If you want to replace the pipe yourself, then you first need to identify which kind of pipe you have. Once that is done, you need to cut the pipe from the place where it has cracked. The next step is to attach a new pipe to the existing one with the help of fittings and clamps. Finally, the repaired pipe is connected to the faucet and it is ready to be used. Or you can give us a call and we will connect you to the best Plumbing Companies in Suitland 20746 MD.

If you follow some of these tips, you can save a lot of money and effort. You can fix the minor leaks yourself, but in case of major leaks or underground damage, it is better to take the help of a professional and licensed plumber. These are some of the things that you need to keep in mind when you are trying to repair a broken pipe line. Now you have all enough information to target the best Plumbing and Heating Contractors Suitland 20746 MD.

References

• http://www.instructables.com/id/Water-Line-Leaks-Fix-It-Yourself-Heres-How/

• http://www.oneprojectcloser.com/how-to-repair-underground-water-pipe/

Related Posts:

#1 24X7 Plumbing and Heating Contractors Earleville 21919 MD (844-507-4350)
#1 24X7 Plumbing and Heating Contractors Elk Mills 21920 MD (844-507-4350)
#1 24X7 Plumbing and Heating Contractors Elkton 21921 MD (844-507-4350)

Plumbing and Heating Contractors Suitland 20746 MD

The most common causes of dripping faucets, are worn washers, bad internal seats or worn/faulty faucet cartridges

Clean visible mold immediately: Surface molds grow in just about any damp location, such as the grout lines of a ceramic tile shower. To get rid of mold, scrub with detergent and water and let the surface dry completely. Or use a solution of 10 percent bleach and 90 percent water (a stronger bleach solution will not give better results). Spray or brush on the solution, let it sit 10 minutes, then rinse it off and let dry. A nontoxic mold control product called Concrobium ($10 for 22 oz. at home centers) can be effective if used every few months.

A pedestal sump pump has the motor attached to the top of a shaft, this motor is not designed to be under water.

Baking Soda, Vinegar, Gravity, and Pressure: If your bath drain is clogged, mix up some of the baking soda/vinegar mentioned in tip two. Pour it down the drain, and then place the stopper over it. After 45-60 minutes, fill the bathtub with water. Then, remove the stopper. The pressure of 40-60 gallons of water should be enough to dislodge the blockage that has been loosened by the baking soda and vinegar. You could also try some plunging or the drain snake in conjunction with the weight of the water.

When cold weather strikes, go into action. Open the cabinets beneath sinks and bathroom fixtures; warmer household air will help prevent the pipes inside from freezing. Opening taps to a bare trickle keeps water flowing and avoids a frozen blockage.

Hit the Salvage Hard: Home decor blogger Anita Joyce found a large piece of salvage barn wood to serve as a shower curtain valance. It looks like a pricey piece and serves as a focal point, but it was definitely a budget item. Salvage can be intimidating, but if you start by checking out antique stores, flea markets, resellers and auctions, you’ve already got the idea, she says. You just have to go do it to really figure it out … and that’s how you score the really great items. You can also salvage and redo cast iron tubs, light fixtures, even sinks … basically anything that fits your style and you want to put the effort in to saving and making your own!

Tips for repairing burst pipes: Replace the old pipes- In case the pipe that has burst is a few years old, it is better to replace it rather than repairing it. The reason is that old pipes become brittle with time due to continuous exposure to water and tend to break. It can so happen that the old pipe that you have recently got repaired, develops a new crack. This means that you have to again spend on getting this leak repaired. This increases the hassle as well as the expense. Therefore, it is better to spend on a new pipe now rather than spending multiple times in the future.

Observe the outlet on your sump pump to make sure water is actually being pumped

How to deal with water damage? Make use of humidity sensors- You cannot spot the moisture that gets seeped into the walls or the ceiling. There are humidity sensors which can help you to locate these wet spots. Once you know which places are most affected, you can start the drying or damage repair process from there. This saves time and helps in tracking the amount of moisture trapped in such inaccessible places. If even a small amount of dampness is allowed to exist, it can cause rot and mold formation which can gradually eat away at the foundation of your house and make it hollow from within. Humidity sensors help in preventing this.

Investigate leaks right away and fix promptly: If you opt to ignore moisture damage or postpone making the necessary repairs, be prepared to experience mold, mildew, dry rot, or even structural damage to your home.

Tips for Fixing Low Water Pressure in Your Home: Take a look at the water heater- Low water pressure can occur in hot water pipes if there is a problem with the water heater. There may be clogging due to sediment accumulation in the heater or the water supply line. The pipes supplying water to the heater may be too narrow. There may be small leaks in the hot water tank or valves. All these reasons can cause the water pressure to become low. It is necessary to eliminate these obstructions in order to make the water flow quickly and with a better force.

Remember to check that whoever completes the work as taken the relevant plumbing courses and gas courses as they should carry their official Gas Safe registered tradesman identity card to get the work done properly and safely!

Tips to Hire a Local Contractor: Take into Account How Long They’ve Been in Business. You want to ask the plumbing company just how long they’ve been in business and how many years of experience the plumber has. A company that has been in business for a long time has shown that they are known in the community for doing quality work.

Tips for Fixing Low Water Pressure in Your Home: Check the water softening system- Many people install a water conditioning system in their homes to get potable water which can be used for daily activities. However, sometimes the water softening system can cause the water pressure to slow down. You should try out the bypass option given in the system to check whether the water supply increases or not. If it does improve, then there is some issue with the softner. You should call a plumber to check the issue with the conditioning system and get it fixed or discard the old system.

Searching quality within cheap prices: Don’t get fooled by the cheap offers or other marketing strategies by some professional plumbing companies. Remember, quality has its price, therefore, do not compromise your safety. And always ask for proof in the form of licenses/certifications as a good company always satisfies its customers through trust building.

Caustic Soda: Get some rubber gloves and eye protection. Caustic soda (also known as Sodium Hydroxide) can cause nasty chemical burns. You can pick some up from your local hardware store, but always use caution handling it. Pour 3/4 gallon of cold water into a mop bucket, and then add 3 cups of caustic soda. Stir it well with an old wooden spoon. It will begin to fizz and heat up. Pour it into the clogged drain and leave for 20-30 minutes, then flush the drain with boiling water. Repeat if necessary.

Remember to use lots of water while running your garbage disposal, to prevent clogs

Sump Pump float switches are design to rise with the rising water levels your basin and the pump is started after the water reaches a certain level.

Keep Plumbing Where It Is: Another reason to work with a designer on your bathroom renovation: Using the existing piping will save you big bucks. Relocating utilities like the toilet and the bathtub are no small task: Designer Justin Riordan says it costs about $5,000 each time you move plumbing fixtures.

Tips for Fixing Low Water Pressure in Your Home: Do not use all the faucets at the same time- It is the most obvious reason for low pressure of water. Generally, when all the members of the family are at home, the use of faucets increases. This usually happens in the morning and the evening. When all the faucets work at the same time, the water supply to the individual faucets decreases. In order to avoid this problem members of the family should make use of the faucets one buy one. This ensures that all the members experience a proper flow of water.

Use a shop vacuum to remove hard objects. When a hard object like a toothbrush, comb or toy plugs a toilet or drain, a plunger may not be the solution—it might only push the obstruction in deeper. Instead, suck out the water and the obstruction with a wet/dry shop vacuum.

How to deal with water damage? Contact water remediation specialists- If your house is flooded with water because of a big leak; you need to contact a plumber to repair the leak and specialist to deal with the damage. The specialist can help you to remove all the wet and damaged contents and start the drying process. It is very important to get rid of all the moisture content from the flooring and the walls to avoid weakening of the foundation. Moisture also encourages the growth of mold. You need to make sure that all your possessions are completely dry before putting them back in their places.

Tips for Fixing Low Water Pressure in Your Home: Locate the water pressure regulator- Many times a water pressure regulator is attached to the main supply valve. It is a wheel-like structure which can either decrease or increase the supply pressure. You can check whether your main supply valve has a regulator or not. If it is there, you can simply adjust it to increase the pressure of the flow of water to your house. It is better to leave this job to a plumber because the regulator is very tight and needs specific tools in order to make adjustments. The plumber also knows how much pressure your pipes can bear so he can make changes accordingly.

Check your water pressure: If the water pressure to your home is set too high, pipes and hoses may fail under the pressure. Buy a water pressure gauge at a local hardware store, attach it to an outside faucet, and turn the faucet to full force. The gauge will give you a reading of the home’s water pressure. Typical residential water systems are designed for water pressure of 40 to 70 psi. If your home’s water pressure exceeds 100 psi, install a pressure regulator (which is available at hardware stores as well.)

What to look for in your next contractor – Find customer reviews of each company online to check the quality of the plumber and his work. Yelp is a great source of customer reviews, but it’s also a great idea to check a more reliable source like the Better Business Bureau before coming to a conclusion. Remember, no one’s perfect so a few bad reviews shouldn’t be a deal breaker. However, if the majority of the reviews are bad or the few bad ones are terrifyingly bad, keep looking.

Tips for repairing burst pipes: Place a rubber over the crack- This is a temporary solution but an effective one. Once you have the situation under control after stopping the water supply, you should put a rubber seal on the area where the pipe has cracked. This stops the water from leaking any further and also holds the pipe in place. There are many such seals available in the market which you can find at any convenience store. This is a quick fix solution for the problem till the plumber comes and takes a look at the pipe.

If you live in areas where sewers tend to back up sometimes, then you should consider installing a backflow valve on your floor drain. This functional yet seemingly simple device is designed to inhibit backups to your floor drain.

Ways to Prevent Washing Machine Leaks: Shut off the faucets after use- After your laundry work is over, you should make it a point to turn off the hot and cold water faucets. If you keep the faucets on, they continue to supply water to the washing machine hoses. The excess water which is not required by the machine gets filled up in the pipes and can cause the hoses to burst. Your laundry can get transformed into a watery mess and the water can seep down to the basement level as well. To prevent such water damage, the simplest trick is to shut the faucets after the spin cycle is over.

Save Money on Bathroom Modelling – Consult an architect. Depending on the scale of your project, you might not need a full–on architectural commission, which involves extensive meetings, multiple job–site visits, and several sets of construction drawings, to the tune of about 8 percent of a project’s construction budget. You might be able to tap an architect’s design savvy by having him undertake a one–time design consultation. For example, for a $400 flat fee, Baton Rouge architect Kevin Harris will meet with a homeowner, examine the problem, and sketch out a few solutions that could be as simple as opening up a partition wall or moving a door. The homeowner can then give the sketch to a builder or take it to a drafting service, which will charge about $1 to $1.50 a square foot to crank out formal construction drawings.

To maintain a sump pump, periodically check the system.

Plumbing Repair Services

We connect you to the best Plumbing Emergency Firms in your city!
6879 Highland Drive
Suitland, MD 20746

Prince Georges, Maryland (MD)

Telephone: 844-507-4350