#1 24X7 Plumbing and Heating Contractors Bel Alton 20611 MD (844-456-4168)Posted by Lee in Heating Contractors, on November 3, 2017
Plumbing Repair Services in Bel Alton 20611
24X7 Operation & FREE Consultation Click to Call
Plumbing and Heating Contractors Bel Alton 20611 MD: Got a broken water line? Here is how you can fix it
The water pipe does not give a warning before breaking. You only get to see the results after the deed is done. The sudden gush of water is the obvious indication of a broken water line. When a water line inside the home gets damaged, it is still easy to fix because it is visible. But in case the underground water line breaks, you need to dig deep into the ground and fix it. This means more hassle and expense. You can go through the tips given below to reduce the expenditure and learn how to fix broken water lines yourself.
Some common reasons for the breaking of water lines
Usually, fittings and connections in the water pipe are the first to get affected and develop cracks which leak and eventually erode the PVC pipe to such an extent that it breaks. The underground water lines located under the foundation of the home or between the street and the house break due to deterioration with the passage of time or due to pressure. In some cases, these pipes burst due to freezing. Water lines also break during earthquakes. When you hear a rumbling or hissing sound coming from the main water line even when you are not using any of the faucets, it means that the main water line has developed a crack. Also, when the pressure of water is lower than usual, it indicates the loss of water due to a leak in the pipe. In such cases, it is very important that you know how to fix broken water lines. Or call us today and we can help you find the best Plumbing Emergency Firms in Bel Alton 20611 MD.
Things that you need to keep in mind before repairing the pipe
It is important to evaluate the condition of the pipe before going for a repair. If the pipe is very old, it is better to replace it rather than trying to repair it. In case the pipe has been repaired before, then too replacement is a good choice. If the pipe has developed a crack for the first time, you should consider removing the whole pipe rather than replacing only the damaged part. The reason is that a repaired pipe is more likely to develop cracks again. So instead of spending money twice on repairing, it is wiser to spend it once and install a new pipe which will last longer. Pipe materials like PVC can be easily repaired but lead based pipes become brittle and corroded with time and hence, need to be replaced.
How to fix broken water lines?
Here are some tips which might prove to be useful in case you want to learn how to fix broken water lines.
- Locating the point of the leak
The first thing is to find the crack. The cracks in the pipes located inside the house are evident but the underground pipes are not visible. When these pipes break, the accumulation of water above the ground or the wet mud gives an indication of the leak. If the pipe located behind the wall of the home breaks, you need to put your ear to the wall and locate the leak. When your pump is running and the water meter is moving without any of your faucets being on, it means there is a leak somewhere. That is why professionals and Plumbing Contractors Bel Alton 20611 MD keep an eye on that.
- Digging under the ground
This advice is given by the top rated Plumbing Repair Services in Bel Alton 20611 MD. The pipes located underground can be repaired only after you dig them out. This is something which you cannot do yourself. You should find a reputable water main contractor to identify the problem and get it fixed. You also need to call your utility company to mark underground pipes and wires so that they do not get damaged when you dig for the water line. When the water line breaks outside the house, the pipe is dug out from the yard to the house. Then it is cut and removed and replaced with a new pipe. The new pipe should be connected with the existing one and all the indoor and outdoor joints should be sealed. You should always check for leaks after the repair work is over. There is also a no-dig repair method in which a resin pipe lining is put in to the pipe till the place of the break. It is then inflated with air so that it touches the wall of the pipe and hardens to seal the pipe. This is called the Cured in Place Pipe method. A minor break can be repaired by putting a sleeve around the pipe or by replacing only that small portion of the pipe.
- Fixing the visible pipes yourself
When you see a sudden gush of water from any pipe of your house, you should first shut-off the main valve. A small leak can be closed by placing a piece of rubber or any other sealing agent available on the leak. You can then put a C-clamp on it to tighten the seal. A sleeve clamp can also be fixed using a screwdriver. It stops both small and large leaks. These plumbing repair items like hose clamps, duct tapes, rubber and C-clamps are very cheap and can be stored at home in anticipation of such problems. If you want to replace the pipe yourself, then you first need to identify which kind of pipe you have. Once that is done, you need to cut the pipe from the place where it has cracked. The next step is to attach a new pipe to the existing one with the help of fittings and clamps. Finally, the repaired pipe is connected to the faucet and it is ready to be used. Or you can give us a call and we will connect you to the best Plumbing Companies in Bel Alton 20611 MD.
If you follow some of these tips, you can save a lot of money and effort. You can fix the minor leaks yourself, but in case of major leaks or underground damage, it is better to take the help of a professional and licensed plumber. These are some of the things that you need to keep in mind when you are trying to repair a broken pipe line. Now you have all enough information to target the best Plumbing and Heating Contractors Bel Alton 20611 MD.
Related Posts:#1 24X7 Plumbing and Heating Contractors Brunswick 21716 MD (844-456-4168)
#1 24X7 Plumbing and Heating Contractors Buckeystown 21717 MD (844-456-4168)
#1 24X7 Plumbing and Heating Contractors Brownsville 21715 MD (844-456-4168)
Plumbing and Heating Contractors Bel Alton 20611 MD
Pay attention to how hardwood meets a tile floor. Chances are, your bathroom will have a tile floor, but the hallway or room it’s connected to will have something totally different, like hardwood. The transition between these two spaces and materials is something that’s tough to get right. As in most cases, planning ahead will give you results that meet your expectations.
WaterSense labeled toilets meet or exceed plumbing standards
Plastic piping is much easier to install, adjust and tighten if a leak develops, than metal piping
Plan the right height for your sink. Typical countertops are 32 to 34 inches off the floor. But you need to consider how your sink will add to or take away from the countertop’s height. If you have an above-counter vessel sink, for example, you’ll want to make your counter height lower so you can wash your hands or brush your teeth comfortably.
Pouring chemicals down your drain will corrode the pipes.
Get a copy of the Uniform Plumbing Code to make sure your plumbing is up to par.
Clogged toilet? Let it sit for a few hours or overnight, then try flushing again. Often times this is all you’ll need to do, to fix the issue. Just be ready for the water to over flow if this doesn’t work.
The Bowl Empties Slowly: A bowl that empties slowly — also known as a weak flush — is usually the result of clogged holes underneath the rim of the bowl. Use a curved piece of wire to poke gently into each flush hole to clear out any debris. Coat-hanger wire works fine, and a small mirror will help you see under the rim. You can also use wire to loosen debris that may be blocking the siphon jet in the bottom of the drain. Be careful not to scratch the bowl.
Consider “smart” bathroom timers and humidity sensors: Bath fan timers are important because excess humidity can cause everything from window condensation and mildew to moisture and rot inside walls. Some new wall switch timers have dual controls for turning off both lights and fans after a preset time. For the ultimate in smart bath fan timers, buy a humidity-sensing fan designed to automatically turn on and off as moisture levels at the ceiling rise and fall.
Tips for repairing burst pipes: Switch off electricity supply to the room- The main water supply pipes are usually present in the attic or basement. When a pipe bursts, you should not only stop the water supply but also the electricity supply to that room. This precaution is necessary because you can get electrocuted by wading through the flood of water if any electric wire becomes loose or if the water comes in touch with an electric socket. Water and electricity is a fatal combination which can prove to be life-threatening. So you should be careful about it.
Plumbing product: First of all, you should try out a live enzyme product like Bio-Clean for the upkeep of your sewer lines. This way, the grease or some other byproducts can keep the lines from getting clogged. While the product is expensive, it can save you lots of hassle down the road.
Submersible sump pumps are typically quieter than pedestal pumps.
Change the showerhead. You can buy a rain showerhead, massage showerhead and other models that will give your bathroom a spa look and feel as well as improve your shower experience. Most of the time, you can make the change in five minutes with a wrench.
Use pipe insulation to prevent sprayer snarls. If you have to jiggle the hose as you pull out your kitchen sink sprayer, chances are the hose is catching on the shutoff valves. For smooth operation, slip 1/2-in. foam pipe insulation over the pipes and shutoff handles. Tape it if it won’t stay put. Get the insulation at home centers for about $3.
Ways in Which You Can Prevent Water Damage: Check the bathroom flooring- Washrooms contain the maximum water supply pipes in the house. These pipes are more prone to damage because of regular use. If they start leaking, they can make the floor damp. Soft spots created by this dampness are generally seen around toilets, sinks, tubs and showers. You should immediately call the plumber to fix the leak to prevent the dampness from spreading to other parts of the bathroom or the house.
Tips for repairing burst pipes: Drain the excess water- After shutting-off the main water supply, you need to make sure that there is no water left in the broken pipe. For this purpose, you need to open all the faucets and flush the toilets. The excess water drains away, leaving the pipe dry and eliminating the possibility of the leaking of water. Once the plumbing system of your house is drained, you can ask a plumber to repair the burst pipe. This makes the process of repairing efficient and quick.
Use a strong magnet to find hidden pipes. When trying to locate a pipe under the floor, attach a rare earth (neodymium) magnet to an electrical fish tape and feed it into drain lines through the cleanout plug. Locate the magnet (and the pipe) under the floor using an ordinary compass, which will turn wildly when it finds the strong magnet.
Remove hoses: You should remove the hoses from the faucets, and you should do this before the faucets freeze in the cold season.
A pedestal sump pump has the motor attached to the top of a shaft, this motor is not designed to be under water.
Keep in mind that homeowner’s insurance provides coverage for damage that is sudden and accidental. Damage that results from lack of maintenance is not covered on a standard homeowners insurance policy. If it’s too late and you’re already dealing with a wet disaster, check out advice on how to minimize water damage in your home.
Using biodegradable soaps will help you conserve more water
Plumbing Repair Services
Bel Alton, MD 20611
Charles, Maryland (MD)